20 ( 20 ) - High quality structural carbon steel:chemical composition, mechanical and physical properties, hardness Database of steels and alloys (Marochnik) contains information about chemical composition and properties more then 3000 steels and alloys ASME SA-372 Grade L ASME SA-372/SA-372M - BBN STEEL ASME SA-372 Grade L ASME SA-372/SA-372M is an alloy of iron and carbon and other elements. Because of its high tensile strength and low cost, it is a major component used in buildings, infrastructure, tools, ships, automobiles, machines, appliances.
Chemical composition and Mechanical Strength. ASTM A106 Grade B and A pipe chemical composition. Chemical composition in %. Carbon (C) Max For Grade A 0.25, For Grade B 0.30, Grade C 0.35. Manganese (Mn):0.27-0.93, 0.29-1.06. Sulfur (S) Max: 0.035. Phosphorus (P) : 0.035. ASTM A372 Grade J Alloy Steel ::MakeItFromMay 30, 2020 · ASTM A372 grade J steel is an alloy steel formulated for primary forming into wrought products. It has a moderately low embodied energy and a moderately low base cost among wrought alloy steels in the same category. The properties of ASTM A372 grade J steel include five common variations. This page shows summary ranges across all of them. DIN 2458 ST37.2 WELDED STEEL TUBES/STEEL PIPES --- Jan 26, 2015 · Designation of a welded steel pipe made of St 37.2, having an outside diameter of pipe 273mm and a wall thickness of 6.3mm :Pipe DIN 2458 - St 37-2 - 273 X 6.3 Welded Steel Tubing and pipe-Corresponding to DIN 2458. DIN2458 St 37.2 welded steel pipe chemical composition
Cast steel Chemical composition of steel G18Mo5 (1.5422), Standards of steel G18Mo5 (1.5422) Mechanical Properties of steel G18Mo5 (1.5422) steel G18Mo5 (1.5422) Tensile Strength, Elongation, Proof strength , Hardness JIS G3101 SS 400 steel plate standard, specification and Heat analysis shall be used to determine the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, and copper. Tensile strength, yield strength, and elongation shall be evaluated using tension test and must conform to the required tensile properties.SS400 is a Japanese standard steel whose material is 1.0037. S355N steel - Gnee steelChemical composition % MAX:C:Mn:Si:P:S:Nb:V:Al:Ti:Cr:Mo:N :0.20:0.45-1.60:0.45:0.035:0.03:0.06:0.07:0.015:0.06:0.35:0.13:0.017 :Mechanical properties MIN:Yield strength (Mpa) Tensile strength (Mpa) Elongation % 16 >1640 >4063 >63 80 >80100 >100150 >150200 >200250 >250400:100 100 200 200250 :275:265:255:245:235:225:215:205-370-510:350-480:
Mar 11, 2012 · The Chemical Composition of SPHC Steels. JIS G 3131 defines the chemical composition of SPHC steels as under:Maximum percentage of Carbon (C) is 0.15 percent. Maximum percentage of Manganese (Mn) is 0.60 percent. Maximum percentage of Phosphorous (P) is 0.050 percent. Maximum percentage of Sulphur (S) is 0.050 percent. ST 37-2 structure steel super heavy steel plateST 37-2 ST 37-2 steel plate mechanical properties:ST 37-2 steel plate is one mainly of Carbon steel, ST 37-2 is a type of steel sheet under EN standard which is used ST37-2 Angle Steel - Low Carbon Steel For General UsesST37-2 Carbon Steel Angle - Galvanized or Pre-Painted ST37-2 is a kind of low carbon steel with carbon content of 0.20%, similar to S235JR or Q235. It's not as strong as common ASTM A36, but it is also widely applied by everyday uses and structural applications where high strength is not so important. ST37-2 angle steel
Designation:A 372/A 372M 03 An American National Standard 4.1.1 The steel melting procedures of Specication A 788 Chemical Composition 5.1 Heat AnalysisThe heat analysis obtained from sam-pling in accordance with SpecicationA 788 shall comply with Table 1.A 372 Grade G Class 65 Chemical Composition, Datasheet for Steel Grades Specialsteel A 372 Grade G Class 65 A 372 Grade G Class 65 Standard Number:ITEM Standard Number Descriptions 1 A 372/A 372M (2012) Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels A 372 Grade G Class 65 Chemical composition(mass fraction)(wt.%) Chemical Min.(%) Max.(%) C 0.40 Si 1.00 Mn 0.65 P S Ni 3.00 Cr 0.70 Al Cu Ti